Forum: Lounge
Yesterday, 10:17 PM
|
Replies: 7
Views: 384
|
Forum: Lounge
Yesterday, 08:41 PM
|
Replies: 7
Views: 384
|
Forum: Lounge
Yesterday, 04:45 PM
|
Replies: 7
Views: 384
It was inevitable.
Had to happen sooner rather then later. The all electric Corvette.
https://www.hemmings.com/stories/chevrolet-confirms-2025-ev-corvette/
I know this is nit picky, but who is educating...
|
Forum: Lounge
04-30-2024, 10:52 PM
|
Replies: 38,829
Views: 8,854,989
|
Forum: Technical & Restoration
04-30-2024, 03:29 PM
|
Replies: 43
Views: 3,915
And that is the problem. I do not have a...
And that is the problem. I do not have a perfectly flat surface.
I have a couple of friends that have body shops. I may contact one of them to see if they can put it on a frame machine and check...
|
Forum: Lounge
04-28-2024, 01:27 AM
|
Replies: 13
Views: 1,491
|
Forum: Ebay & other seen ads section
04-25-2024, 09:49 PM
|
Replies: 8
Views: 1,625
|
Forum: Parts/Memorabilia - Wanted
04-23-2024, 01:38 AM
|
Replies: 12
Views: 1,387
|
Forum: Technical & Restoration
04-21-2024, 05:15 PM
|
Replies: 43
Views: 3,915
|
Forum: Supercars/Musclecars-Wanted
04-20-2024, 02:15 AM
|
Replies: 89
Views: 15,496
|
Forum: Supercar/Musclecar Discussion
04-18-2024, 10:18 PM
|
Replies: 18
Views: 1,953
|
Forum: Ford-Mercury
04-15-2024, 12:38 PM
|
Replies: 16
Views: 3,221
|
Forum: Technical & Restoration
04-15-2024, 02:09 AM
|
Replies: 43
Views: 3,915
Holley Carb. Apparently, the original was...
Holley Carb. Apparently, the original was swapped out somewhere along the way.
This one looks pretty grimy, but it ran perfectly. No hesitation; no flat spots.
Has correct metering plates. ...
|
Forum: Technical & Restoration
04-15-2024, 01:57 AM
|
Replies: 43
Views: 3,915
|
Forum: Technical & Restoration
04-15-2024, 01:51 AM
|
Replies: 43
Views: 3,915
Yup. Eyes wide open. I knew is would be a...
Yup. Eyes wide open. I knew is would be a challenge.
All the shims are simply thick aluminum washers on this car.
All are corroded to some extent, with some being worse, and several are in...
|
Forum: Lounge
04-14-2024, 02:30 PM
|
Replies: 7
Views: 696
|
Forum: Lounge
04-14-2024, 02:28 PM
|
Replies: 10
Views: 1,278
Pics of my 10 10 Z/28
Given the prices of some of the 69 Z/28's lately, I decided to up the coverage. Tami at MK said that wasn't a problem, but underwriting wanted some contemporaneous photos.
So, got it out...
|
Forum: Technical & Restoration
04-13-2024, 12:33 PM
|
Replies: 43
Views: 3,915
That is what I thought. I don't know how they...
That is what I thought. I don't know how they determined what thickness went where. I am guessing the frames were pretty consistent but the bodies were not so consistent.
This frame has enough...
|
Forum: Technical & Restoration
04-12-2024, 10:27 PM
|
Replies: 43
Views: 3,915
|
Forum: Technical & Restoration
04-08-2024, 09:13 PM
|
Replies: 2
Views: 638
|
Forum: Technical & Restoration
04-08-2024, 04:09 AM
|
Replies: 43
Views: 3,915
First question:
The gas tank has lots of...
First question:
The gas tank has lots of surface rust. The inside is spotless. Is it worth restoring?
New ones can be had for less than $300.
With Konis and side pipes, I am obviously not...
|
Forum: Technical & Restoration
04-08-2024, 04:03 AM
|
Replies: 43
Views: 3,915
No Going Back now. 70 LT-1
Decided to go all in.
Pulled the body off the frame yesterday. Even with my gantry crane at 12 feet high, I had to tie the harness in a knot to get enough clearance to roll the chassis out from...
|
Forum: Technical & Restoration
04-06-2024, 02:16 PM
|
Replies: 12
Views: 971
I have something similar on my Z. But it is...
I have something similar on my Z. But it is pretty inconspicuous on the back of the engine almost obscured by the distributor. I think Jake is looking for something less conspicuous, given that his...
|
Forum: Technical & Restoration
04-05-2024, 07:58 PM
|
Replies: 12
Views: 971
|
Forum: Lounge
04-02-2024, 01:24 AM
|
Replies: 13
Views: 1,491
|