Re: 37 Ford LS2 Continuation thread
 

First off.............The "Tangle" of wires is disappearing.........

http://i13.photobucket.com/albums/a2...t/DSC01147.jpg

And I have all the outside A.C. and heater lines crimped and assembled.......the break in the two smaller lines in the pic is where the Filter/Drier goes.........

http://i13.photobucket.com/albums/a2...t/DSC01145.jpg

Also got the gas tank vent put in.......I positioned it high in the wheel well opening where it will be covered by the fender and high enough to do the job.....It has a small slotted screened area that is facing away from where the tire would throw stuff that is where the vent opening is

http://i13.photobucket.com/albums/a2...t/DSC01148.jpg

http://i13.photobucket.com/albums/a2...t/DSC01149.jpg

As I was digging around looking for some parts today I came across the coil covers and just for the heck of it I put them on....I didn't think they would fit, and they dropped right on.........

http://i13.photobucket.com/albums/a2...t/DSC01151.jpg

Now............At this point Dave said "Let's see if it will start"..........Hit the key and it started Imediately.....Wow!!.......I didn't have much faith in the engines starting with the complexity of the wiring and everything else.....Just go's to show that Dave and the GM Engineers know what they are doing......Even the drive by wire gas pedal worked https://www.yenko.net/ubbthreads/imag...iggthumpup.gif

Ken (with a smile on my face)

Re: 37 Ford LS2 Continuation thread
 

Congrats Ken! Looking great and coming along!!!

"Ken (with a smile on my face)"

http://img.photobucket.com/albums/v6...humbawamba.jpg

Re: 37 Ford LS2 Continuation thread
 

Awesome! Keep smiling https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

Re: 37 Ford LS2 Continuation thread
 

That is COOL!

Re: 37 Ford LS2 Continuation thread
 

is this turd done yet..??

Re: 37 Ford LS2 Continuation thread
 

Spent the day today getting the car down on the ground and and setting the pinion angle.....Wheels and tires are still not in..........

http://i13.photobucket.com/albums/a2...t/DSC01156.jpg

Got the steering linkage in and finished

http://i13.photobucket.com/albums/a2...t/DSC01157.jpg

Picked up all the new side and rear window glass also....Next week we will get all the inside hoses hooked up, get the heat and defrosters hooked up.....Radiator Hoses and get the Door internals installed and put the doors on.....Off to the upholstry shop in a week

http://i13.photobucket.com/albums/a2...t/DSC01158.jpg

Ken

Re: 37 Ford LS2 Continuation thread
 

Man-O-Man Ken, Looks great and even runs. https://www.yenko.net/ubbthreads/imag...iggthumpup.gif https://www.yenko.net/ubbthreads/imag...ns/worship.gif https://www.yenko.net/ubbthreads/imag...ins/3gears.gif

Re: 37 Ford LS2 Continuation thread
 

In addition to making a bunch of parts and gaskets to clean up and seal the installation of the windshield wipers (install and pic's tomorrow) I got the air intake pretty much finalized, after I get the front sheetmetal installed I will be making a cold air box to draw outside air in thru the Hood sides.........Lot's of misc parts coming in this week to finish everything up.........

http://i13.photobucket.com/albums/a2...t/DSC01164.jpg

http://i13.photobucket.com/albums/a2...t/DSC01163.jpg


Ken

Re: 37 Ford LS2 Continuation thread
 

nice , your getting close to firing it up, no rod is complete without a drive around the lot sitting on the milk crate. https://www.yenko.net/ubbthreads/imag...lins/beers.gif

Re: 37 Ford LS2 Continuation thread
 

The air intake looks great...

I remember all of the looking at SEMA for just the right part...