TANK STICKER CORVETTE
 

ANY ONE KNOW THE BEST WAY TO REMOVE A TANK STICKER FROM THE GAS TANK ?
THANKS
LES

Re: TANK STICKER CORVETTE
 

The best way is to leave it on the tank and install another tank. Just a opinion....

Re: TANK STICKER CORVETTE
 

Agree with Charlie 100% on this one. Most everyone regrets removing it after they do the deed and usually end up messing it up at least a little. A 45 year old car can probably use a new gas tank anyway.

Re: TANK STICKER CORVETTE
 

My was coming apart so I just clear taped it to the tank after I took pictures of it and put it back up.

http://i245.photobucket.com/albums/g...78/8-30461.jpg


http://i245.photobucket.com/albums/g...78/8-30501.jpg

Re: TANK STICKER CORVETTE
 

THANKS GUYS. ANY MORE TIPS I AM OPEN I WOULD LIKE TO HERE MORE.
THANKS

LES

Re: TANK STICKER CORVETTE
 

[ QUOTE ]
THANKS GUYS. ANY MORE TIPS I AM OPEN I WOULD LIKE TO HERE MORE.
THANKS

LES

[/ QUOTE ]
the best thing to do is cut it out still attached to the tank and put it in a secure area https://www.yenko.net/ubbthreads/imag...ns/scholar.gif

Re: TANK STICKER CORVETTE
 

[ QUOTE ]
[ QUOTE ]
THANKS GUYS. ANY MORE TIPS I AM OPEN I WOULD LIKE TO HERE MORE.
THANKS

LES

[/ QUOTE ]
the best thing to do is cut it out still attached to the tank and put it in a secure area https://www.yenko.net/ubbthreads/imag...ns/scholar.gif

[/ QUOTE ]

The cut-out piece is a little easier to store in a safe-deposit box/fire safe than the whole tank...unless your Charley and have a vault for your money...

To take it a step further I would video/document the removal of the tank as further proof that it came from a particular car. Since there is not a vin# on a tank sticker anything you can do to provide additional documentation is a plus.

Re: TANK STICKER CORVETTE
 

It would be terrible to cut up a good original tank if it was a ZL! or L88 or even a special car why wouldnt somebody put plastic over it and just use the tank most cars arent driven anyways. My car isnt a high dollar car but still wont be driven in a lot of bad weather

Re: TANK STICKER CORVETTE
 

Be careful how you cut the tank. You cannot use any grinders with sparks, or something like a plasma cutter. If you do, you'll have bigger problems than a ripped tank sticker.

-Dave

Re: TANK STICKER CORVETTE
 

That's actually something I've considered doing. Taking a plasma cutter and VERY carefully cutting out about 3 inches or so around the sticker itself.

Re: TANK STICKER CORVETTE
 

Drill some starting holes in the empty and rinsed tank and then take a jigsaw/sawzall or tin snips and cut it out leaving a metal margin around the outside. Then you can take the cutout piece and finish the sharp edges on your bench grinder.

Re: TANK STICKER CORVETTE
 

ALL GREAT TIPS GUYS I KNOW THAT WITH KNOWLEDGE OF THE GUYS HERE ON THIS SITE THAT I WOULOD GET SOME GREAT ANSWERS. I WILL KEEP EVERY ONE POSTED IF I GO LOOK AT THE CAR.
LES

Re: TANK STICKER CORVETTE
 

If you have other paperwork, cover it and leave it on the tank after taking good pictures.

Re: TANK STICKER CORVETTE
 

[ QUOTE ]
The best way is to leave it on the tank and install another tank. Just a opinion....

[/ QUOTE ]

There's a good chance the tank has pin holes on the bottom anyway. I hardly ever saw a Corvette tank that didn't have an inch or so of water in the bottom.
I had to replace the tank in my '68 and still have it (with the sticker attached) stored above my garage. The car is long gone but much of the stuff I replaced is still around. BTW, Anyone need a complete smog pump and brackets for a '68 427 Corvette? https://www.yenko.net/ubbthreads/imag...ns/naughty.gif

Re: TANK STICKER CORVETTE
 

Maybe be off the topic a bit, but if one choses to cut or repair a tank, after it is cleaned out, through in a few pounds of dry ice. That will displace the 02 and may keep you off the local news too.
I have seen some old welders ( like Shoney. https://www.yenko.net/ubbthreads/imag...mlins/grin.gif) use this trick on small aircraft tanks.