Forum: Chevrolet
02-24-2022, 01:58 AM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-23-2022, 12:26 AM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-17-2022, 01:15 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-17-2022, 12:55 AM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-15-2022, 10:01 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-15-2022, 09:33 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
04-29-2021, 09:34 PM
|
Replies: 114
Views: 44,077
This project is coming to an end (at least for...
This project is coming to an end (at least for now). I replaced all of the suspension bushings along with all new ball joints, tie rods, idler, etc. The timing is set, engine is tuned, brakes are...
|
Forum: Chevrolet
04-01-2021, 03:19 PM
|
Replies: 114
Views: 44,077
The trans is here, the shifter is adjusted...
The trans is here, the shifter is adjusted (installed the 65 shifter arms for a shorter throw), and now everything is installed or at least mocked up. I suspect an install is in the cards today or...
|
Forum: Chevrolet
03-26-2021, 09:14 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
03-23-2021, 05:56 PM
|
Replies: 114
Views: 44,077
I started to make the plug wires and screw it...
I started to make the plug wires and screw it together today. Waiting on different terminal ends for the distributor side of the wires (wasn't impressed with what came in the set).
I've got to...
|
Forum: Chevrolet
03-22-2021, 09:12 PM
|
Replies: 114
Views: 44,077
A couple of experiments with Chevy Orange, some...
A couple of experiments with Chevy Orange, some black (dusting each) and then following up with a scuff pad........this is what I came up with.
I think once it gets some heat cycles in it (as well...
|
Forum: Chevrolet
03-20-2021, 12:54 PM
|
Replies: 114
Views: 44,077
A good friend of mine brought me the engine...
A good friend of mine brought me the engine yesterday, so I had a chance to get into the shop early this morning to assemble a few things. Your thoughts.........should I dust some paint on the motor...
|
Forum: Chevrolet
03-08-2021, 07:07 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
03-05-2021, 10:54 PM
|
Replies: 114
Views: 44,077
I've been working on the 64 a little bit, not...
I've been working on the 64 a little bit, not much as I've been working on a couple of other cars I have in my shop (67 L79 Corvette and a 68 Z28).
I spoke to the engine builder today. He dyno'd...
|
Forum: Chevrolet
02-16-2021, 05:56 PM
|
Replies: 114
Views: 44,077
In less than a month.....the long block is...
In less than a month.....the long block is complete. On to the dyno next week!
https://i.imgur.com/26ic65zh.jpg
I got my booster back from Mike Gibbons just in time. Great service......thanks...
|
Forum: Chevrolet
02-10-2021, 02:40 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
02-10-2021, 02:10 PM
|
Replies: 114
Views: 44,077
The machine shop is wasting no time. The block...
The machine shop is wasting no time. The block only required a hone (at .030 still), the crank only required polishing. I went with new rods and pistons that will get me in the 10.5:1 neighborhood...
|
Forum: Chevrolet
01-25-2021, 04:45 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-20-2021, 06:53 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-19-2021, 12:03 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-14-2021, 12:29 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-13-2021, 08:07 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-13-2021, 05:26 PM
|
Replies: 114
Views: 44,077
|
Forum: Chevrolet
01-13-2021, 01:38 PM
|
Replies: 114
Views: 44,077
Taking down to the machine shop towards the end...
Taking down to the machine shop towards the end of the month. It will get whatever it needs. We'll see if the bores will take just a hone, or will need to be opened up to .040 or .060. The recipe I...
|
Forum: Chevrolet
01-12-2021, 04:55 PM
|
Replies: 114
Views: 44,077
My Dad was around this weekend, so I put him to...
My Dad was around this weekend, so I put him to work for a little bit. Shocking what he'll do from some free beer! We snatched the motor out so I can get cooking. Hard to believe he and I have been...
|