#21
|
|||
|
|||
----As far as I know this beauty should have a close ratio 4-speed. In 65 paperwork did not differentiate between close and wide ratio. The engine options you chose determined which trans you got within a certain ratio. What I don't know is weather a customer could over ride the system and get a specific trans to fit his or her use. For instance an ordered 375 hp with a desired 3:70 rear would automaticly get a close ratio 4-speed. If the owner wanted a 3:08 or 3:36 that car would get a wide ratio trans. Hope this makes sense.....Bill S
Last edited by olredalert; 12-14-2021 at 09:06 PM. |
The Following User Says Thank You to olredalert For This Useful Post: | ||
MarcDant (12-14-2021) |
#22
|
||||
|
||||
Do you know when the mm 22 phased in. Thanks
|
#23
|
|||
|
|||
----There are examples thruout 1965 of very rare instances of ordered cars with M-22's. I have a good friend that has a 1965 396 Corvette with it's original stampted M-22 still intact. Engine gone, but stamping on the trans as well as early anomalies (rough castings and such) are right there. Don't know the date at this time but it is real! There are other examples tha some of the guys may expand upon!....Bill S
|
#24
|
||||
|
||||
A friend ordered a '65 BelAir L78/M22 in Feb, received it in June.
|
The Following User Says Thank You to 67since67 For This Useful Post: | ||
olredalert (12-15-2021) |
#25
|
|||
|
|||
First Corvette M22 Rock Crusher
A buddy whose race shop was 2 doors from mine ordered and took delivery of the first Corvette to have an assembly line M22, 194375S118966 was a blk/blk L78 tanker, "rush order-competition car" March 22/65, as Dave planned to run it in sports car races, which he did quite successfully. He traded in a blk/blk 1963 SWC fuelie that he had raced. I had all of the original sales docs and passed them on to the current collector owner, it having long been in good hands.
|
The Following User Says Thank You to midyr For This Useful Post: | ||
Ryan1969Chevelle (12-16-2021) |
#26
|
||||
|
||||
Bill do you know if your friends 65 m22 has a 1 inch or the early 7 / 8 cluster shaft. Thats a healthy bel air 67since67 . Midyr holy grail 6, the L72 with 3.36 rear ratio must a lot of fun on the roads (rare ratio for a 425 Hp) .Thanks gents.
|
#27
|
|||
|
|||
----Sorry, can't help about that as the car resides about 5 states from me.....Bill S
|
#28
|
||||
|
||||
pre-delivery sheet
Took this pre-delivery sheet pic from holy grail 6 and noticed differences between a canadian 69-70 pre delivery sheet i found in my protecto plate folder of my car not filled out. You must be familiar with these sheets.
|
#29
|
|||
|
|||
Paper
Sometimes it seemed back then The General was more interested in producing paper than vehicles. There was always a blizzard of the stuff. Get a form one week and a couple of weeks later it was superseded by another, and another, and another. Salesman order books always had blank lines to write in changes and cost increases, cause they just kept coming.
The vast majority of it just got tossed, and even if put in a file dealers routinely sent it all to a landfill every five years or so, needing the room for more paper to come. Attached are Zone announcements for the L35 and Z28 availability in January 1967. The point now would be to recognize how rare the old docs are today, especially when directly relating to a specific car. |
The Following 3 Users Say Thank You to midyr For This Useful Post: | ||
Thread Tools | |
Display Modes | |
|
|