Day 2 67 Camaro restoration - Page 48

**Chuck_Burg** · #**471** 10-18-2023, 04:43 PM

I can tell you the Torker works just fine. Power wherever you want it... It just falls off too soon. If I don't like the Tarantula, I can always put the Torker back on

GrumpyJeff · #**472** 10-18-2023, 10:04 PM

Quote:

Originally Posted by Chuck_Burg

Thanks guys!

It ready has a single plane on it Mitch, a Torker. Plus it’s a 496” engine, don’t think it’ll lose much torque lol

Tire pressure isn’t the issue, watch the rear bounce up. Needs a better shock, which is in the works. Got a very experienced drag racer helping me with this.

I run those same tires on my 67 @18lbs, minor burn out like yours , generic NAPA shocks on rear, 90/10 drag shocks on front , I leave at 3500 shift at 6000 1.57 60 ft

**Chuck_Burg** · #**473** 10-19-2023, 08:45 PM

That is hookin' and bookin'! What gear do you have?

**napa68** · #**474** 10-19-2023, 08:53 PM

Quote:

Originally Posted by Chuck_Burg

I can tell you the Torker works just fine. Power wherever you want it... It just falls off too soon. If I don't like the Tarantula, I can always put the Torker back on

In the name of 60' times, you probably could afford to give up some torque

**Chuck_Burg** · #**475** 10-19-2023, 09:01 PM

I agree Tim! I don't have the intention to race much but you know how addicting it is...

SPEEDYB · #**476** 10-20-2023, 02:30 AM

Sounded good at Irwindale, I was there!
Im sure that 496 will respond good with that
Tarantulas bigger port volume.

**Chuck_Burg** · #**477** 10-20-2023, 03:40 AM

Thanks Speedy! It’s got plenty left in it. My buddy who built the engine and I have been looking for a TM2-O for a while with no success. Want this when we built the engine back in 2019! You going to In-N-Out 75 at Pomona this Sunday?

SPEEDYB · #**478** 10-20-2023, 01:51 PM

We were going to race at Pomona but the event is sold out!
Ill keep my eyes peeled for an oval port Tarantula thou!

**Chuck_Burg** · #**479** 10-20-2023, 06:52 PM

I'm running at Pomona

I found the Tarantula! Taking it to get Vaporhoned today

**Chuck_Burg** · #**480** 11-01-2023, 05:34 PM

We had a blast at Pomona. Good times with friends and family. I got to make two passes, should've been three but I blew a heater hose in the burnout box and had to get pushed off the track

haha. Talk about embarrassing in front of almost full grand stands

Best was a 12.17 @114mph. The car was starving for fuel (sputtering on the big end at the top of 3rd gear and 4th gear) so I made a jet change and it actually hurt it more. Fuel pump can't keep up with demand....

I was really thinking it would run high 11s considering the weight of the car, over 3600lbs without driver, and the 3.55 gears so I'm close. I am going to convert the car to 1/2 hard fuel line with a 1/2" pickup and an Edelbrock mechanical pump.

After the track I conducted a fuel pump volume test after talking to some drag racing buddies. I removed the fuel line on the secondary float bowl and plugged it into a rubber hose draining into plastic jug. My mechanical pump only pumped 8-9oz of fuel in 12 seconds. Turning on my electric pump, which I had on during the runs at the track, I saw 29oz of fuel in 12 seconds which is about .2 gallons. Probably very close to the amount of fuel I need in a 1/4 mile... too close for comfort!

Not that the car is a drag car but I want to be prepared next time. Some things can only be discovered on the track!

After I install my new fuel lines and pump, I will install the Tarantua TM2-O intake and bring it to the dyno to make sure we have enough fuel!

The Following 3 Users Say Thank You to Chuck_Burg For This Useful Post:
jbtech (10-18-2023), napa68 (10-18-2023), Xplantdad (10-18-2023)

The Following 2 Users Say Thank You to GrumpyJeff For This Useful Post:
Chuck_Burg (10-19-2023), napa68 (10-19-2023)

The Following User Says Thank You to Chuck_Burg For This Useful Post:
ACR (10-20-2023)

The Following User Says Thank You to napa68 For This Useful Post:
Chuck_Burg (03-28-2024)

The Following User Says Thank You to Chuck_Burg For This Useful Post:
napa68 (10-19-2023)

The Following User Says Thank You to SPEEDYB For This Useful Post:
Chuck_Burg (10-20-2023)

The Following 2 Users Say Thank You to Chuck_Burg For This Useful Post:
dykstra (10-20-2023), napa68 (10-20-2023)

The Following 9 Users Say Thank You to Chuck_Burg For This Useful Post:
1-slow-camaro (11-02-2023), dykstra (11-02-2023), L_e_e (11-01-2023), markinnaples (11-02-2023), napa68 (11-01-2023), olredalert (04-17-2024), SMS (11-10-2023), x77-69z28 (11-03-2023), Xplantdad (11-01-2023)