Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
#1
05-03-2021, 03:41 PM
|
||||
|
||||
Chevelle updates
Decided to do a little updating, correcting, and cleaning up of my Chevelle this late winter/spring.
I've had this car since 1987 - my first car. I have the original born with 402/240 engine on a stand in the corner of the garage and back in 2000-ish installed a GMPP 454/425 crate motor and made it appear like the original 402 as much as I could. Things were looking a bit tired under the hood and I wanted to go through the brakes and install some of the original parts back on the car. I started disassembly back in February. Last edited by RPOLS3; 05-03-2021 at 05:47 PM. 
|
| The Following 5 Users Say Thank You to RPOLS3 For This Useful Post: | ||
Damien (05-03-2021), dykstra (05-05-2021), kwhizz (05-25-2021), PeteLeathersac (05-03-2021), SS427 (05-03-2021) | ||
|
#2
05-03-2021, 03:51 PM
|
||||
|
||||
|
This whole project started out as a carb replacement. I had installed a generic speed shop Holley on the crate motor and wanted something more correct, so I called Eric and he sent me a fresh real 4492. I couldn't bolt this piece of jewelry on my existing setup without some clean up and re-freshing of the other major components.
|
| The Following 5 Users Say Thank You to RPOLS3 For This Useful Post: | ||
1972convss454 (05-03-2021), big gear head (05-03-2021), dykstra (05-05-2021), kwhizz (05-04-2021), Xplantdad (05-03-2021) | ||
|
#3
05-03-2021, 03:54 PM
|
||||
|
||||
|
Did some paint touch up and re-plated the heater hose fittings and clamps - still the dated originals.
|
| The Following 4 Users Say Thank You to RPOLS3 For This Useful Post: | ||
|
#4
05-03-2021, 04:00 PM
|
||||
|
||||
|
I sent out the master cylinder and calipers to NAPA to be rebuilt, had the original brake dust shields galvanized, and had a local plater re-do the gold on the caliper mounting brackets (and smog check valves). I sent the booster and master cylinder cover to Mike Gibbons. Re-detailed some of the other components I had to remove as well.
|
| The Following 7 Users Say Thank You to RPOLS3 For This Useful Post: | ||
1972convss454 (05-03-2021), big gear head (05-03-2021), dykstra (05-05-2021), kwhizz (02-22-2022), olredalert (05-17-2021), ORIGLS6 (05-24-2021), Xplantdad (05-03-2021) | ||
|
#5
05-03-2021, 04:04 PM
|
||||
|
||||
|
Decided to upgrade the wheel and tire package while I was at it too. I haven't got it back on the ground yet to drive though.
|
| The Following 8 Users Say Thank You to RPOLS3 For This Useful Post: | ||
1972convss454 (05-03-2021), dykstra (05-05-2021), GearheadSS (10-05-2021), kwhizz (05-04-2021), olredalert (05-17-2021), ORIGLS6 (05-24-2021), PeteLeathersac (05-03-2021), Xplantdad (05-03-2021) | ||
|
#6
05-03-2021, 04:06 PM
|
||||
|
||||
|
Worked with Bill Hodel to get a correctly dated and restored smog pump and peripherals. More jewelry.
|
| The Following 4 Users Say Thank You to RPOLS3 For This Useful Post: | ||
|
#7
05-03-2021, 04:08 PM
|
||||
|
||||
|
Sent my original alternator out to Ken Bruno and had him work his magic on it.
|
| The Following 6 Users Say Thank You to RPOLS3 For This Useful Post: | ||
1972convss454 (05-03-2021), dykstra (05-05-2021), kwhizz (02-22-2022), olredalert (05-17-2021), ORIGLS6 (05-24-2021), Xplantdad (05-03-2021) | ||
|
#8
05-03-2021, 04:11 PM
|
||||
|
||||
|
Still waiting on my fuel pump back from Fred Ballard so I can finish the re-assembly of the front of the engine and fire it up. Also waiting on the rear cylinders from Karp's to complete the brakes, will install a new rubber line on the rear to the distribution block as well. It's been and enjoyable project as I am not on a hard deadline and have the space - but hope to have it complete soon to be able to enjoy the summer season. Will post more as I make more progress - thanks for following along.
|
| The Following 6 Users Say Thank You to RPOLS3 For This Useful Post: | ||
1972convss454 (05-03-2021), dykstra (05-05-2021), kwhizz (02-22-2022), ORIGLS6 (05-24-2021), Too Many Projects (05-05-2021), Xplantdad (05-03-2021) | ||
|
#9
05-03-2021, 04:11 PM
|
|||
|
|||
|
Nice updates
Are the foam pads hanging by doors there to prevent door dings?
|
|
#10
05-03-2021, 04:13 PM
|
|||
|
|||
|
LOVE IT!!!
__________________
Don't mistake education for intelligence. I worked with educated people. I socialize with intelligent people.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
