Forum: Muscle Car and Corvette Nationals
Today, 12:21 AM
|
Replies: 23
Views: 2,316
|
Forum: Muscle Car and Corvette Nationals
Yesterday, 01:00 PM
|
Replies: 23
Views: 2,316
|
Forum: Muscle Car and Corvette Nationals
09-24-2024, 08:54 PM
|
Replies: 23
Views: 2,316
Thanks for the info everyone. I'm thinking to...
Thanks for the info everyone. I'm thinking to book my flights were I can get time in both days. Looks like the hotel shuttle will take me where I need to go so no need for a rental car. I just...
|
Forum: Muscle Car and Corvette Nationals
09-22-2024, 11:12 PM
|
Replies: 23
Views: 2,316
|
Forum: Muscle Car and Corvette Nationals
09-21-2024, 12:57 PM
|
Replies: 23
Views: 2,316
First Time at MCACN
Hey guys, I’m planning on going this year and it will be my first time coming to the show. I flew into O’hare for the first time earlier this year for business and noticed the convention center was...
|
Forum: Technical & Restoration
08-21-2024, 01:08 PM
|
Replies: 3
Views: 499
|
Forum: Technical & Restoration
08-20-2024, 07:55 PM
|
Replies: 3
Views: 499
1967 Camaro Upper Door Hinge Rebuild
Well, after 26 years of ownership my upper door hinge has begun to sag on the drivers side. I'd prefer to rebuild the original hinge if possible rather than replacing it with an aftermarket part. ...
|
Forum: Supercar/Musclecar Discussion
08-16-2024, 07:30 PM
|
Replies: 19
Views: 2,892
If you want to hammer on it with no worries of...
If you want to hammer on it with no worries of what happens to the engine, go with more displacement. I have a 406 small block with AFR's, super victor, and a hydraulic flat tappet in my 67 Camaro...
|
Forum: Technical & Restoration
07-09-2024, 07:26 PM
|
Replies: 5
Views: 811
|
Forum: Technical & Restoration
07-09-2024, 06:59 PM
|
Replies: 5
Views: 811
|
Forum: Technical & Restoration
07-08-2024, 10:18 PM
|
Replies: 5
Views: 811
|
Forum: Technical & Restoration
07-08-2024, 12:01 AM
|
Replies: 5
Views: 811
|
Forum: Garages/shops..
06-27-2024, 01:43 PM
|
Replies: 32
Views: 14,404
|
Forum: Garages/shops..
06-26-2024, 08:33 PM
|
Replies: 32
Views: 14,404
Looks good! I put two 84" fans from home depot...
Looks good! I put two 84" fans from home depot on down rods in my 40x60 shop and they move a considerable amount of air and keep it comfortable. However, once outside temps are above 90 degrees, it...
|
Forum: Preservation forum
06-26-2024, 06:47 PM
|
Replies: 268
Views: 132,062
|
Forum: Mopar
06-19-2024, 02:48 PM
|
Replies: 14
Views: 9,205
|
Forum: Mopar
06-19-2024, 02:37 PM
|
Replies: 14
Views: 9,205
Moving on to the engine, it was evident that it...
Moving on to the engine, it was evident that it was filthy, 50+ years of grime, grease and makeshift repairs, it was leaking from every conceivable orifice, but it ran very well, so I decided to put...
|
Forum: Mopar
06-19-2024, 01:46 PM
|
Replies: 14
Views: 9,205
Continuation from the post yesterday. After...
Continuation from the post yesterday. After examining the internals of the trans, everything looked good, so I cleaned it up, replaced the input shaft and output shaft seals and reinstalled the top...
|
Forum: Mopar
06-18-2024, 09:23 PM
|
Replies: 14
Views: 9,205
Well, I've been hard at work on this Truck for...
Well, I've been hard at work on this Truck for the past few months. I'll add posts as I get time to show the progress. I was able to fix all of the oil leaks, replaced the timing set, cleaned the...
|
Forum: Supercar/Musclecar Discussion
05-06-2024, 06:26 PM
|
Replies: 17
Views: 5,650
|
Forum: Mopar
04-26-2024, 01:30 PM
|
Replies: 14
Views: 9,205
No worries Mitch. I've always liked Mopars as...
No worries Mitch. I've always liked Mopars as well. The truck I'm working on now has been a part of my life since I was about a year old. My dad bought it in the mid 80s and used it for his...
|
Forum: Mopar
04-25-2024, 12:46 AM
|
Replies: 14
Views: 9,205
|
Forum: Mopar
04-24-2024, 11:04 PM
|
Replies: 14
Views: 9,205
|
Forum: Day 2 stuff-modified cars
04-24-2024, 08:30 PM
|
Replies: 12
Views: 9,657
|
Forum: Mopar
04-24-2024, 07:56 PM
|
Replies: 14
Views: 9,205
Oil Pan Sealing Tips LA Small Block?
I'm in the process of putting a clutch in my 69 D300 and while the transmission is out, I am fixing the oil leaks coming from the pan. Do you guys have a certain method of installing the gaskets &...
|